49. Відділ матеріалознавства та інженерії високостійких поверхневих шарів
Постійне посилання на фондhttps://archive.ipms.kyiv.ua/handle/123456789/80
Переглянути
4 результатів
Результати пошуку
Документ EFFECT OF THE STRUCTURE OF TiB2–(Fe–Mo) PLASMA COATINGS ON MECHANICAL AND TRIBOTECHNICAL PROPERTIES(Powder Metallurgy and Metal Ceramics, 2017) M. S. Storozhenko; A. P. Umanskii; A. E. Terentiev; I. M. Zakiev2The structure, mechanical properties, and wear-resistance of TiB2–(Fe–Mo) plasma coatings are investigated. Composite powders in the TiB2–(Fe–Mo) system with 20, 40, 60, and 80 wt.% of the Fe–13 wt.% Mo alloy were produced by vacuum sintering with subsequent grinding. The developed powders are conglomerates that contain both refractory and metallic phases. During plasma spraying of developed coatings, a coating with heterophase structure, which consists of Fe-based metal alloy and titanium diboride grains, is formed. The effect of the microstructure of plasma-sprayed coatings on the wear-resistance under abrasive wear and dry sliding friction conditions is studied. The scratch hardness testing revealed an insufficient strength of TiB2–20 wt.% (Fe–13 wt.% Mo) coatings and their poor adhesion to the coating base, resulting in the extremely gross wear, when friction. It is found out that, due to the optimal ratio of refractory and metallic phases, the TiB2–40 wt.% (Fe–13 wt.% Mo) coating possesses high wear-resistance under abrasive wear and dry sliding friction conditions.Документ STRUCTURE, PHASE COMPOSITION, AND WEAR MECHANISMS OF PLASMA-SPRAYED NiCrSiB–20 wt.% TiB2 COATING(Powder Metallurgy and Metal Ceramics, 2015) A. P. Umanskii; M. S. Storozhenko; I. V. Hussainova; A. E. Terentiev; A. M. Kovalchenko; M. M. AntonovThe structure, phase composition, and wear mechanisms of plasma-sprayed NKhTB20 coating (NiCrSiB–20 wt.% TiB2) are studied. To produce NKhTB20 composite powder, commercial PR-NKh16SR3 (NiCrSiB) powder was mixed with 20 wt.% TiB2 and the charge was pressed and sintered in vacuum at 1100C for 30 min. During sintering, the components react to form chromium borides. The sinters were ground and classified into the particle size fraction –100+60 nm for plasma spraying. The plasma-sprayed NKhTB20 coating consists of a nickel-based matrix reinforced with titanium diboride and chromium boride grains. The friction and wear behavior of the NKhTB20 coating in dry friction against plasma-sprayed NiCrSiB and NKhTB20 coatings is examined. It is revealed that the NKhTB20/NiCrSiB friction pair has higher wear resistance than NKhTB20/NKhTB20. The contact surfaces of the NKhTB20/NKhTB20 friction pair are damaged under oxidative and abrasive wear mechanisms. Oxidative wear is the dominant mechanism for the NKhTB20/NiCrSiB friction surface. Complex oxide films form on the NKhTB20/NiCrSiB sliding surface and prevent it from damage.Документ Effect of oxidation on sliding wear behavior of NiCrSiB-TiB2 plasma sprayed coatings(Key Engineering Materials, 2014) O. Umanskyi; I. Hussainova; M. Storozhenko; O. Terentyev; M. AntonovThe main goal of this work is to study dry sliding wear behavior of NiCrSiB-TiB2 plasma sprayed coating against NiCrSiB coating. NiCrSiB-based сomposite powders with 10, 20, 40 wt.% TiB2 particles content were deposited on steel substrates by plasma spraying. The structure of NiCrSiB-TiB2 coatings consists of Ni-based matrix and TiB2 and CrB grains. Among the coatings studied, the NiCrSiB-20wt.%TiB2 shows excellent wear-resistance. The worn surfaces were observed using scanning electron microscopy and Auger electron spectrometry analysis to determine the wear mechanisms.